- 您现在的位置：买卖IC网 > Sheet目录307 > ADP3415LRMZ-REEL (ON Semiconductor)IC MOSFET DVR DUAL BOOTST 10MSOP
ADP3415
Shutdown
For optimal system power management, when the output voltage
is not needed, the ADP3415 can be shut down to conserve power.
When the SD pin is high, the ADP3415 is enabled for normal
operation. Pulling the SD pin low forces the DRVH and DRVL
outputs low, turning the buck converter OFF and reducing the
VCC supply current to less than 40 μ A.
Bootstrap Circuit
The bootstrap circuit requires a charge storage capacitor, C BST ,
and a Schottky diode, D1, as shown in Figure 2. Selecting these
components can be done after the high-side FET has been chosen.
The bootstrap capacitor must have a voltage rating that is able
to handle the maximum battery voltage plus 5 V. The capaci-
tance is determined using the following equation
Undervoltage Lockout
The undervoltage lockout (UVLO) circuit holds both FET
driver outputs low during VCC supply ramp-up. The UVLO
C BST =
Q GATE
? V BST
(1)
logic becomes active and in control of the driver outputs at a
supply voltage of no greater than 1.5 V. The UVLO circuit
waits until the VCC supply has reached a voltage high enough
to bias logic level FETs fully ON, around 4.1 V, before releas-
ing control of the drivers to the control pins.
Thermal Shutdown
The thermal shutdown circuit protects the ADP3415 against
damage due to excessive power dissipation. Under extreme
conditions, high ambient temperature and high power dissipa-
tion, the die temperature may rise up to the thermal shutdown
where Q GATE is the total gate charge of the high-side FET,
and V BST is the voltage droop allowed on the high-side FET
drive. For example, the IRFR8503 has a total gate charge of
about 15 nC. For an allowed droop of 150 mV, the required
bootstrap capacitance is 100 nF. Use an MLC capacitor.
A Schottky diode is recommended for the bootstrap diode due
to its low forward drop, which maximizes the drive available for
the high-side FET. The bootstrap diode must also be able to
withstand the maximum battery voltage plus 5 V. The average
forward current can be estimated by
threshold of 165 ° C. If the die temperature exceeds 165 ° C, the
thermal shutdown circuit will turn the output drivers OFF. The
I F ( AVG ) ≈ Q GATE × f MAX
(2)
drivers remain disabled until the junction temperature has
decreased by 10 ° C, at which point the drivers are again enabled.
APPLICATION INFORMATION
Supply Capacitor Selection
For the supply input (VCC) of the ADP3415, a local bypass
capacitor is recommended to reduce the noise and to supply
some of the peak currents drawn. Use a 10 μ F MLC capacitor.
Keep the ceramic capacitor as close as possible to the ADP3415.
Multilayer ceramic (MLC) capacitors provide the best combina-
tion of low ESR and small size and can be obtained from the
following vendors:
where f MAX is the maximum switching frequency of the controller.
Delay Resistor Selection
The delay resistor, R DLY , is used to add an additional delay
when the low-side FET drive turns off and when the high-side
drive starts to turn on. The delay resistor programs a specified
additional delay besides the 20 ns of fixed delay.
Printed Circuit Board Layout Considerations
Use the following general guidelines when designing printed
circuit boards:
1. Trace out the high current paths and use short, wide traces
to make these connections.
Murata
Taiyo-Yuden
Tokin
GRM235Y5V106Z16
EMK325F106ZF
C23Y5V1C106ZP
www.murata.com
www.t-yuden.com
www.tokin.com
2. Locate the VCC bypass capacitor as close as possible to the
VCC and GND pins.
Rev. 6 | Page 9 of 10 | www.onsemi.com
REV. B
–9 –
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ADP3419JRM-REEL
IC MOSFET DVR DUAL BOOTST 10MSOP
ADP3611JRMZ-REEL
IC MOSFET DRIVER DUAL 10-MSOP
ADP5501ACPZ-RL
IC LED DRVR WHITE BCKLGT 24LFCSP
ADP8863ACPZ-R7
IC LED DRVR WHIT BCKLGT 20-WLCSP
ADUM1100UR
IC DIGITAL ISOL/COUPLER 8SOIC
ADUM1201CR
IC ISOLATOR DIGITAL DUAL 8SOIC
ADUM1210BRZ
IC ISOLATOR DIGITAL DUAL 8SOIC
ADUM1233BRWZ-RL
IC ISOLATR DGTL 2CH 0.1A 16-SOIC
相关代理商/技术参数
ADP3415LRMZ-RL7
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Dual MOSFET Driver with Bootstrapping
ADP3416
制造商:AD 制造商全称:Analog Devices 功能描述:Dual Bootstrapped MOSFET Driver
ADP3416JR
制造商:Rochester Electronics LLC 功能描述:DUAL MOSFET DRIVER - Bulk
ADP3416JR-REEL
制造商:Rochester Electronics LLC 功能描述:DUAL MOSFET DRIVER - Tape and Reel
ADP3416JRZ-REEL
功能描述:IC MOSFET DRIVER DUAL 7V 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:低端 输入类型:非反相 延迟时间:40ns 电流 - 峰:9A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:4.5 V ~ 35 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263 包装:管件
ADP3417
制造商:AD 制造商全称:Analog Devices 功能描述:Dual Bootstrapped MOSFET Driver
ADP3417JR
制造商:Rochester Electronics LLC 功能描述:DUAL 12V MOSFET DRIVER - Bulk
ADP3417JR-REEL
制造商:Rochester Electronics LLC 功能描述:DUAL 12V MOSFET DRIVER - Tape and Reel